CWP

    Central Dialysis Water System

    The CWP 100 offers cost-effective, consistent delivery of AAMI grade water according to ANSI/AAMI/ISO 13959:2009 for dialysis at the point of use. This system is designed to meet all current standards for dialysis quality water. The automated heat disinfection of the distribution loop simply and easily reduces biofilm development and minimizes levels of endotoxin, fungi, yeast and other microbial contaminants.

    automated heat disinfection Enery efficient      

     

M4 RO System

  • Features
  • Specifications
  • Literature
  • Tech Documents

Standard Features
• Hot water loop disinfection
• Medical-grade Wirsbo-cleanPEX® distribution system
• Direct feed operation
• Automated disinfection of the loop and semi-automated disinfection of RO membranes
• Integrated end-to-end heat with the Phoenix ® Hemodialysis System
• Monitoring software for documentation and verification of disinfection procedures
• 510(k)-cleared as a water purification system for hemodialysis

• ETL certified
Optional Items
Mar Cor Purification offers a complete line of components and accessories, including:
• Blending Valves and Booster Pumps
• Multi-Media Filters
• Water Softeners
• Carbon Adsorption
• Hardness and Total Chlorine Test Kits
• AAMI Water Analysis
• Chemical Disinfectants

 
   
  CWP 100 Specifications
   
  Product Water - Minimum capacity at 20˚C and at a pure water outlet pressure of 29 psi(200 kPa)
  Output Model  
101
102
104
106
  Part Number  
100975
101366
100474
103256
  Product Water in gallons/min (l/min)
3.4 (13)
5.3 (20)
7.7 (29)
9.3 (35)
  Quality Depends on inlet water quality. The system is designed to utilize drinking water that meets the standards of the Safe Drinking Water Act, 40 CFR. Additional pretreatment of inlet water is required. A properly maintained system using inlet water meeting SDWA can obtain the following rejection rates:
  Total dissolved salts > 95 %   •   Bacteria (CFU) & endotoxins > 99 %   •   Water conversion factor 67 %
   
  Water Supply
  Input Model  
101
102
104
106
  Min Input flow in gallons/min (l/min)
5.3 (20)
7.9 (30)
13.2 (50)
15.9 (60)
  Min Input pressure in psi (kPa)
15 (100)
15 (100)
36 (250)
51 (300)
  Max Input pressure in psi (kPa)
73 (500)
73 (500)
73 (500)
73 (500)
  Temperature +5˚C to +25˚C*      *(Maximum +20˚C if peracetic acid is used for disinfection)
     
  Drain Requirements
  Peak Flow (Rinse) Model  
101
102
104
106
  Required capacity in gallons/min (l/min)
5.3 (20)
7.9 (30)
13.2 (50)
15.9 (60)
  Note: Maximum flow occurs during flushing
   
  Reverse Osmosis Membranes
  Material Modified polyamide, thin film composite
  Configuration Spiral wound
  pH-Tolerance 2–11
     
  Power Supply
  Main Voltage 120/208 V, 60 Hz, 3-phase (5 wires)
  Power rating RO-unit 101-104: 1.8 kW; RO-unit 106: 2.5 kW; Heating unit 101-106: 9.0 kW
  Fuse 16 AT + 32 AT, 16 (slow blow) or 40 AT (slow blow) one supply

 


   
  Manuals P/N
  CWP Manual - Model H-S Operations Guide 3027367
   
  Tech Notes
  TN123-Minimum GAC Volumes Needed for EBCT-3002463f.pdf 10/28/2011
  TN231-CWP Chemical Pump Uptake System 8/1/2012
  TN232-Identifying CWP Main RO Pump Replacement Parts 8/1/2012
  TN235-CWP H-S-P New PLC and HMI 10/5/2012
  TN240-CWP Inlet Solenoid Information 6/21/2013
  TN241-Updated Preventive Maintenance Procedure 6/21/2013
  TN242-Changes to CWP Valves and PM Kits 6/21/2013
  TN243-Lowering Conductivity Alarm Limits Below Standard Range 6/25/2013
  TN246-Adjusting Dayligh Savings Time for CWP with E1032 Operator Panel 8/20/2013
  TN247-CWP GXL Remote Access Technote 8/27/2013
     
  General Tech Notes Date
  TN102-Recovery-3002413.pdf 1/16/2009
  TN103-Hemodialysis Water Quality Standards-3002433g.pdf 2/7/2009
  TN104-Nominal Rejection Characteristics of Reverse Osmosis Membranes-3002434c.pdf 1/16/2009
  TN107-Resistivity Measurement-3002435c.pdf 1/16/2009
  TN108-Flow and Volume Equivalents-3002436c.pdf 1/16/2009
  TN111-Water Quality Conversion Table-3002437c.pdf 1/16/2009
  TN112-Unit Conversion Tables-3002438c.pdf 1/16/2009
  TN113-Temperature Correction Factors for Thin Film Membranes-3002432e.pdf 5/25/2011
  TN114-Unit of Measure and Their Abbreviations-3002409c.pdf 1/16/2009
  TN115-Useful Formulas-3002430c.pdf 1/16/2009
  TN116-AAMI Analysis-3003016c.pdf 1/27/2009
  TN117-Concentrations of Toxic Effects to Dialysis Patients-3002431c.pdf 1/16/2009
  TN118-Chemical Names, Common Names and Formulas-3002459c.pdf 1/16/2009
  TN119-Most Commonly Asked Questions-3002460d.pdf 10/20/2011
  TN120-Glossary of Terms-3002461c.pdf 1/16/2009
  TN122-Chemical Toxic Effects in Drinking Water-3002462c.pdf 1/16/2009
  TN128-Wire Connections-3002978c.pdf 1/27/2009
  TN158-RO Cleaning Disinfecting Considerations-3003010d.pdf 1/22/2010
  TN159-Alarm Set Point for RO Machines-3003013d.pdf 2/3/2012
  TN195-RO Operation On High Temp Feed Water-3026689a.pdf 4/20/2010
   

Copyright © 2006–2014 Mar Cor Purification . All rights reserved.